Search found 5353 matches

by datzenmike
01 Dec 2018 22:43
Forum: Powertrain
Topic: Trans slips 5th gear
Replies: 6
Views: 211

Re: Trans slips 5th gear

Any FSM from Nissan with your transmission in it will have the chart. Once the cover plate is removed you'll see that there is a shim around the outside of the counter bearing. (it's the bottom or smaller of the two bearings) The measurement is how far the bearing sits proud of the case that support...
by datzenmike
30 Nov 2018 20:49
Forum: Powertrain
Topic: Trans slips 5th gear
Replies: 6
Views: 211

Re: Trans slips 5th gear

The shims are select fit at the factory to allow for production inaccuracies. It corrects the front cover plate for proper pre-load on the counter bearing. Either way you would only need to remove the 5 cover plate bolts and the cover plate to get at it to make two measurements and then check the ch...
by datzenmike
17 Nov 2018 07:16
Forum: General Discussion
Topic: Is this ok price for a 510 4dr?
Replies: 7
Views: 299

Re: Is this ok price for a 510 4dr?

While possible, a one owner is very rare. Service documents would really help here as a provenance. No rust is also very rare and subjective... there is always some rust somewhere if you look. Was it repainted? maybe repaired at some time? 100% stock is also very rare as some things can't easily be ...
by datzenmike
16 Nov 2018 20:58
Forum: Classifieds
Topic: WTB Z20E Rods 152.5mm
Replies: 5
Views: 270

Re: WTB Z20E Rods 152.5mm

Byron I doubt the Mileage option was available here. I have a feeling it was a Federal only package in the States. I've never seen one up here. I parted an '80 L20B 4x4 years ago. I have had 2 S110s (an '80 and an '81) that I parted out. Sold one set of rods into the States and Jason Wong took the o...
by datzenmike
14 Nov 2018 19:21
Forum: Classifieds
Topic: WTB Z20E Rods 152.5mm
Replies: 5
Views: 270

Re: WTB Z20E Rods 152.5mm

In the US the '80-'81 A10 (HL510) the '80-'81 S10 (2nd gen 200sx) and the '83-'86.5 720 with the Mileage option Z20 engine, all have the 152.5mm (6") rods in them. The part number is 12100-N8500
by datzenmike
08 Nov 2018 19:41
Forum: General Discussion
Topic: Photobucket trying to blackmail me.
Replies: 15
Views: 1606

Re: Photobucket trying to blackmail me.

Never!!! I've never looked back. Now all old pictures are marred with "Proudly hosted on photobucket"??? really? May they all fall into Dante's 9th circles of hell... alternating between the 4th circle for Greed ... https://historylists.org/images/greed.jpg and the 9th for Betrayal. https://historyl...
by datzenmike
02 Nov 2018 20:12
Forum: Not Datsun/Nissan related?
Topic: Binky!
Replies: 55
Views: 6147

Re: Binky!

I lost interest when they re-invented the heater.
by datzenmike
12 Oct 2018 22:48
Forum: Powertrain
Topic: Help to find an L20B flywheel in Europe
Replies: 3
Views: 199

Re: Help to find an L20B flywheel in Europe

All six cylinder and 4 cylinder 2 liters and more are 6 bolt mount to the crankshaft and will interchange. They were drilled to accept either a 200mm 225mm or a 240mm pressure plate. 6 bolt flywheels can weigh either 29 or 21 pounds. So if you have a 225mm 29 pound wheel it will weigh more than a 24...
by datzenmike
07 Oct 2018 20:59
Forum: Engine Swap
Topic: SR20DET Oil Pump Priming
Replies: 10
Views: 598

Re: SR20DET Oil Pump Priming

Assuming the oil pump works, push oil back through the pump instead of air. That will fill it and the pick up tube.
by datzenmike
19 Sep 2018 19:06
Forum: Powertrain
Topic: questions on a 32/36 install
Replies: 4
Views: 384

Re: questions on a 32/36 install

That hose connects to the flow guide valve mounted low on the strut tower it's pointing at. The flow guide valve does several things depending if the engine is running or not. When off, it allows evaporated gas from the tank (under very slight positive pressure) into the engine crank case for storag...
by datzenmike
18 Sep 2018 20:52
Forum: Powertrain
Topic: questions on a 32/36 install
Replies: 4
Views: 384

Re: questions on a 32/36 install

http://clunkbucket.com/wp-content/gallery/1973-datsun-510/datsun_510_slots2.jpg The block vent should be connected to the PCV valve in the intake as shown in the picture. The valve cover vent should go to the air filter housing. I hate when people fuck with this beautifully simple and benign system...
by datzenmike
17 Sep 2018 19:42
Forum: Body & Electrical
Topic: Stock 240sx distributor housing
Replies: 1
Views: 128

Re: Stock 240sx distributor housing

It's called a crank angle sensor (CAS) and needs the ECU and sensors to set the spark and correct advance. It might be useful if going to something like a Mega Jolt system.
by datzenmike
17 Sep 2018 19:38
Forum: Powertrain
Topic: R160 Diff ID
Replies: 7
Views: 386

Re: R160 Diff ID

39/10=3.9
by datzenmike
12 Sep 2018 21:15
Forum: Powertrain
Topic: "83 280ZX close ratio box and 3:90 differential
Replies: 18
Views: 848

Re: "83 280ZX close ratio box and 3:90 differential

Not everyone who has a Datsun has a 'true' close ratio box, would even know about them, where to find one, could afford one, and if they did they probably wouldn't like them anyway for their predominantly street driven cars. The 'close ratio' box is simply too esoteric for a street car. So that leav...