Search found 11678 matches

by Byron510
22 Jan 2018 22:28
Forum: Events
Topic: All Japanese Classic '18 - August 26th - Waterfront Park
Replies: 17
Views: 320

Re: All Japanese Classic '18 - August 26th - Waterfront Park

Bring it out Leonard - I have black electrical tape for the emblems :-)

You still have the R5, right? Park then side by side.

Byron
by Byron510
22 Jan 2018 17:10
Forum: Project Builds
Topic: Another 72 510
Replies: 51
Views: 3141

Re: Another 72 510

Pressure is on!!!

:D

Byron
by Byron510
22 Jan 2018 17:08
Forum: Events
Topic: All Japanese Classic '18 - August 26th - Waterfront Park
Replies: 17
Views: 320

Re: All Japanese Classic '18 - August 26th - Waterfront Park

Byron, I guess the Spring Show is long gone. With the Renault - Nissan - Mitsubishi alliance does that qualify Renaults to be 'somewhat" Japanese? It's so lonely not having a car show to belong to. :( Caesardx I will make an exception for your car - Show organizer, I can pull that string :-) S...
by Byron510
22 Jan 2018 17:04
Forum: Introductions
Topic: Datsun sSS 1600 L16 project
Replies: 1
Views: 29

Re: Datsun sSS 1600 L16 project

So tell us where you are location is, and what your skills are.

There are many resources here on theRealm - welcome.

Byron
by Byron510
20 Jan 2018 06:18
Forum: Project Builds
Topic: Five-Hundred and Ten
Replies: 27
Views: 566

Re: Five-Hundred and Ten

Just browsed through your photo album, great to see your documentation by photos. I am glad to see that your crossmember was not rotted through behind the factory inner bracket when you removed it. I have found a number of crossmembers lately- ones that looked much better than yours on the surface -...
by Byron510
19 Jan 2018 21:08
Forum: Introductions
Topic: New member in Alberta
Replies: 7
Views: 123

Re: New member in Alberta

Welcome. I saw the Kijiji ad in Sask if that's the same car. It's on it's second set of floors and due again. Trunk floor is done, and it looks like the rockers have been done at least once. And it looks like it's had fairly good drivers side damage if the panels have been replaced as pictured. Not ...
by Byron510
19 Jan 2018 19:30
Forum: Powertrain
Topic: Cam etching/engraving decipering
Replies: 8
Views: 165

Re: Cam etching/engraving decipering

Actually it may not be as strong as you think. I'm not sure what the duration is on the cam you have, as that can affect a compression test. My motor is a stock 2.2 bottom end like yours with a slightly milled head. I measured the CR on mine to be 10.7:1 with an early U-67 head. Compression was 185 ...
by Byron510
19 Jan 2018 06:32
Forum: Events
Topic: All Japanese Classic '18 - August 26th - Waterfront Park
Replies: 17
Views: 320

Re: All Japanese Classic '18 - August 26th - Waterfront Park

what about an autox? I’d love to have an AutoX organized on the same weekend, but I need people to run it. The show organization is just Richard and I, it’s a lot of work to make this show happen. Added to that, Richard also started a brand new family this year (yeah - congratulations) so his time ...
by Byron510
19 Jan 2018 06:12
Forum: General Discussion
Topic: Air Conditioning for 72 4 dr. w/vg30?
Replies: 11
Views: 259

Re: Air Conditioning for 72 4 dr. w/vg30?

I’ll find a photo of the center mount air vent for the late style dash for you David, it’s the only one I’ve ever seen in person. However there is reference to it in the factory and Haynes manual drawings. The AC part for me isn’t the only thing I need. As noted earlier I removed the heater in my yo...
by Byron510
18 Jan 2018 10:11
Forum: General Discussion
Topic: Air Conditioning for 72 4 dr. w/vg30?
Replies: 11
Views: 259

Re: Air Conditioning for 72 4 dr. w/vg30?

Nice job. I have a factory AC under dash unit, and an optional late style center dash fresh air vent. I’d love to incorporate one or both into my installation. Likely just the AC unit, but we’ll have to see. I still need the heater and AC box, condenser and dryer to mount somewhere with plumbing to ...
by Byron510
18 Jan 2018 03:00
Forum: Powertrain
Topic: Cam etching/engraving decipering
Replies: 8
Views: 165

Re: Cam etching/engraving decipering

Sounds like Z22 pistons were used on a re-bore. These had the four valve reliefs which you mentioned. Sure it’s not a Z22 block? Is there an engine stamp pad on the drivers or LH side of the block - the opposite side of the oil filter? As for which gasket to use, for many years I have used the NapsZ...
by Byron510
17 Jan 2018 19:05
Forum: General Discussion
Topic: Air Conditioning for 72 4 dr. w/vg30?
Replies: 11
Views: 259

Re: Air Conditioning for 72 4 dr. w/vg30?

Pics? I'd love to see details. In my youthful exuberance, I removed the heater out of the Bronze. Now in my mid 40's, I see the error in my ways! I have felt for many years that if I add a heater, I may as well add AC....with the compressor placed under that custom EFI manifold I made some years ago...
by Byron510
17 Jan 2018 18:53
Forum: Introductions
Topic: Soon to be new 510 owner
Replies: 10
Views: 230

Re: Soon to be new 510 owner

Looks good. Diff looks like it might be an R180 (did I miss that in the post?) If so, it could be anything from a 3.36 to 4.62....

For the price, it's a good runner and a good base. I'd say you did well.

Byron
by Byron510
17 Jan 2018 18:46
Forum: Project Builds
Topic: 1971 2 Door, L16 --> 2.1 Long Rod --> SR20VE
Replies: 378
Views: 35006

Re: 1971 2 Door, L16 --> 2.1 Long Rod --> SR20VE

Photos are all good on my PC...

Keep up the good work and posts.

Byron
by Byron510
17 Jan 2018 18:44
Forum: Body & Electrical
Topic: Factory Tachometer Install with EI - Resistorr Size for use with EI Dizzy
Replies: 18
Views: 267

Re: Factory Tachometer Install with EI - Resistorr Size for use with EI Dizzy

As current is the same anywhere in a circuit, being ahead of the coil or after may not matter... BUT it must be in line. I do recall though reason of deduction that this inductive pick up won't work in line on the negative side from the coil on the way to the distributor. I am not an electronics gu...

Go to advanced search