Search found 11539 matches

by Byron510
25 Jul 2017 22:22
Forum: Powertrain
Topic: Throwout bearing question
Replies: 7
Views: 99

Re: Throwout bearing question

The NTN one would be Japanese made, and I would trust the quality therem- provided it's the right part in the first place :-)

Byron
by Byron510
24 Jul 2017 22:31
Forum: Powertrain
Topic: Throwout bearing question
Replies: 7
Views: 99

Re: Throwout bearing question

Mike, I might have to disagree with you as the one on the right is an original diameter L16 TO bearing used on 510's. The one on the transmission is a later 225mm TO bearing used first on the pick ups. As Robyn noted, both will work. But they will feel different to the driver. You may not think it, ...
by Byron510
20 Jul 2017 05:49
Forum: Classifieds
Topic: EFI Manifolds For Sale, IR for Datsun L-Series heads
Replies: 38
Views: 4243

Re: EFI Manifolds For Sale, IR for Datsun L-Series heads

No deposit required, I just need my milling machine in place so that I can machine these up :-).

Work on the garage is progressing, contractors are lined up. I hope to have the machines in place by September, with electrical work then to follow.

Will keep you posted.

Byron
by Byron510
19 Jul 2017 05:02
Forum: Classifieds
Topic: WTB 71-73 front seat belt reciever
Replies: 6
Views: 172

Re: WTB 71-73 front seat belt reciever

Good morning Ryan, Thanks for the offer, however I need the belt receiver with the center push button style. I found The below photo on the net of the style I'm looking for, only I need the one front reciever. IMG_9162.JPG Dean, thank you for your response, is the unit you have the type pictured by ...
by Byron510
18 Jul 2017 22:27
Forum: Powertrain
Topic: CV Failure
Replies: 51
Views: 999

Re: CV Failure

I just replaced the first of 8 CV's on my Armada - 385 lb/ft of torque.... all seven remaining joints appear fine after 200K+ kms and it weighs 6100 lbs!
:-)

Byron
by Byron510
18 Jul 2017 22:23
Forum: Body & Electrical
Topic: Door Lock Issue
Replies: 6
Views: 144

Re: Door Lock Issue

The most common issue... the linkage literally bends over time, which changes the range the lock tumbler and leaver can move the mechanism....

Just a place to start, anyways.

Byron
by Byron510
18 Jul 2017 22:17
Forum: Body & Electrical
Topic: Front windshield seal from Vintage rubber
Replies: 3
Views: 110

Re: Front windshield seal from Vintage rubber

I don't know how much of a hurry you are in, but I'm putting together a Datsport order in the next couple of months if you wanted to share shipping....

Drop me a line, I may have something for you.

Byron
by Byron510
17 Jul 2017 20:58
Forum: Not Datsun/Nissan related?
Topic: B.C. BURNS
Replies: 16
Views: 433

Re: B.C. BURNS

Here's a link to an interactive map, and current situation of each fire.

http://governmentofbc.maps.arcgis.com/a ... kPoint=300

Byron
by Byron510
17 Jul 2017 05:29
Forum: Classifieds
Topic: WTB 71-73 front seat belt reciever
Replies: 6
Views: 172

WTB 71-73 front seat belt reciever

As noted, I'm looking for 1 front seat belt receiver (lower part with the button/latch) for 71-73 style seat belt. I put a set in my brothers car but one of the button/release mechanisms is broken. I used a rear belt base but it's far too short to be used up front. A local Vancouver/BC part would be...
by Byron510
17 Jul 2017 05:24
Forum: Featured Project Builds
Topic: 1972 510 2dr --STRESS RELIEF--
Replies: 972
Views: 73511

Re: 1972 510 2dr --STRESS RELIEF--

Nearly half of these cars were delivered with white interiors, yet you rarely see one today - refreshing to see. Looks great Chad.

Byron
by Byron510
16 Jul 2017 08:27
Forum: Classifieds
Topic: WTB L-16 Lower Alternator mount
Replies: 12
Views: 218

Re: WTB L-16 Lower Alternator mount

As noted in your drawing above, there are a few oddball exceptions. The three bolt mount to the block started on late L16 block, but I have seen early L18 blocks with only the 2x 10mm mount configuration (still better than the 2x 8mm used on most L13/16 blocks). I have also seen the 2x 8mm fabricate...
by Byron510
15 Jul 2017 07:24
Forum: Classifieds
Topic: WTB L-16 Lower Alternator mount
Replies: 12
Views: 218

Re: WTB L-16 Lower Alternator mount

The later L16 blocks did upgrade to the 10mm bolt size and this continued right through production to the end of the L series engines. If the holes in your alternator accept a 10mm bolt, I would suggest drilling and tapping these to the larger size as well. Another good trick I've done is drill the ...
by Byron510
10 Jul 2017 08:48
Forum: Project Builds
Topic: Shawn’s ‘72 Driver
Replies: 171
Views: 14949

Re: Shawn’s ‘72 Driver

So the car has sat in the garage for the last two weeks an not moved at all since this recent work was done. I was in the shop last night and noticed that the fluid in the clutch master cylinder had turned colour already...damn! Must be a CMC or clutch slave cylinder going bad, I can't think of any ...
by Byron510
10 Jul 2017 06:02
Forum: Introductions
Topic: New from Sunny South Africa
Replies: 63
Views: 5132

Re: New from Sunny South Africa

That's a pretty funny photo for sure.

Man that shell still looks pretty good from this angle. Too bad you were not in NA, a fellow member here could have used your RH front corner.

So how's the actual project coming? Updates?

Byron
by Byron510
10 Jul 2017 05:59
Forum: Featured Project Builds
Topic: USA to Western Australia my two door 510 build
Replies: 288
Views: 21149

Re: USA to Western Australia my two door 510 build

Which product did you end up using for insulation on the floors & firewall?

Car looks great, and it's an unusual colour on a 510, can't wait to see it on its wheels outside.

Byron

Go to advanced search