Search found 162 matches

by TheHeretic
18 Jul 2017 10:37
Forum: Suspension
Topic: NVH Issues
Replies: 40
Views: 1394

Re: NVH Issues

Yeah my neighbor has a drive-on hoist I can use. Didn't think it would make a difference as being IRS the diff is locked in place and not moving whether the wheels are up or down. So when you say equally you mean both right and left front shims get moved to the top and the rear shims stay in place?
by TheHeretic
18 Jul 2017 10:30
Forum: Powertrain
Topic: CV Failure
Replies: 49
Views: 902

Re: CV Failure

Confirmed with Troy that his CV Axle Kit may need around 7 or 8 pumps of grease annually. Already have some grease spatter on my coilovers which is normal per Troy. Spoke with Baz at Datsport, MadDat, and The Driveshaft Shop. They all said that the kits they make or did make (Baz) don't require any ...
by TheHeretic
17 Jul 2017 11:40
Forum: Suspension
Topic: NVH Issues
Replies: 40
Views: 1394

Re: NVH Issues

Drove the car today at highway speeds and just the slight decrease in angularity difference from 1.6 degrees down to 1.4 degrees made a difference at 80mph. Thinking of removing the spacer between tranny and mount and trying to adjust just using the differential. So to tilt the differential the righ...
by TheHeretic
15 Jul 2017 14:05
Forum: Suspension
Topic: NVH Issues
Replies: 40
Views: 1394

Re: NVH Issues

Working on trying to get every bit of vibration out of my driveline as I start to feel some during acceleration and at speeds above 75+mph. Was able to get my 510 on a lift this past week and measure what I believe are the right spots on the driveline but would love someone to verify that. As I writ...
by TheHeretic
07 Jul 2017 09:45
Forum: Powertrain
Topic: CV Failure
Replies: 49
Views: 902

Re: CV Failure

So the new Ermish CV kit does have built-in grease fittings which is nice. Also while there are 4 bungs (right word?) for the grease only two have the fittings while the others just have a plug. Troy mentioned that it was to avoid the inner fittings being ripped out from low ground clearance and I w...
by TheHeretic
05 Jul 2017 15:29
Forum: Project Builds
Topic: The Red Baron
Replies: 60
Views: 5521

Re: The Red Baron

Went to Rebello to drop off the oil pan and timing cover for the new engine and was able to see the forged JE pistons for the 2360cc build. Who knew that a piston could look so beautiful?! LOL.

Image
by TheHeretic
05 Jul 2017 15:16
Forum: Powertrain
Topic: CV Failure
Replies: 49
Views: 902

Re: CV Failure

I have Troy's new improved kit (not sure if that means they will last longer?) but he did tell me that they should be regreased every year or so. BUT the job sounded more like simple maintenance with 10 squirts using a grease gun to each grease fitting once a year. Don't know why the Futofab ones wo...
by TheHeretic
04 Jul 2017 14:59
Forum: Project Builds
Topic: The Red Baron
Replies: 60
Views: 5521

Re: The Red Baron

Car is back from Troy's and the new CV kit and aluminum driveshaft made a big difference in a reduction in NVH. Still noticing a minor vibration at speeds above 75mph so will likely need some tinkering with the driveline angle to make it as smooth as possible. Today the modified oil pan showed up fr...
by TheHeretic
27 Jun 2017 10:04
Forum: Suspension
Topic: NVH Issues
Replies: 40
Views: 1394

Re: NVH Issues

Much better now! When putting in the new KA24 transmission we were able to lower the rear of tranny quite a lot compared to the dogleg that was in there before. A significant decrease in vibration when accelerating. Still something very slight but that's before getting the car up on a lift again and...
by TheHeretic
25 Jun 2017 16:31
Forum: Classifieds
Topic: Misc 510 Parts for Sale
Replies: 0
Views: 232

Misc 510 Parts for Sale

JDM Bluebird Front Sidemarker Lights - Lenses are the Japan Domestic Market Straight Arrow Style. They are the Non-USA version. Bulbs, gaskets, and harness are included. These are 100% genuine OEM from Nissan and brand new. $200 http://i.imgur.com/lELEIwv.jpg http://i.imgur.com/fWwMzMq.jpg http://i....
by TheHeretic
24 Jun 2017 13:07
Forum: Powertrain
Topic: Mikuni Intake question.
Replies: 2
Views: 119

Re: Mikuni Intake question.

That will work fine and is a common "shorty" Mikuni intake. Doesn't flow as well as the "longer" Datsun Comp one BUT does allow you to run full velocity stacks. Think it's for sale near me on CL for $400. IMHO overpriced and should be closer to $250.
by TheHeretic
24 Jun 2017 13:04
Forum: Suspension
Topic: Spring Rate Feedback
Replies: 9
Views: 244

Re: Spring Rate Feedback

Well after chatting with Troy Ermish and riding in a few 510s this weekend I'm probably going with 200lb springs all the way around for now. Seems like a nice compromise between what Julian likes (175lbs) and what many 510s run which is closer to 250lbs. Still well more than double what a stock 510 ...
by TheHeretic
22 Jun 2017 11:45
Forum: Suspension
Topic: Spring Rate Feedback
Replies: 9
Views: 244

Spring Rate Feedback

Recently put 250lb/in spring in the rear coilovers and after driving around am thinking they might be a little too much. Especially at 65mph+ the ride in the rear gets harsh. Have unknown front springs which will be updated soon. Leaning towards having a slightly higher rear spring rate and running ...
by TheHeretic
14 Jun 2017 15:13
Forum: Project Builds
Topic: The Red Baron
Replies: 60
Views: 5521

Re: The Red Baron

Getting work done at Troy Ermish's shop in Tracy, CA. Originally I was going to just install the tranny myself but the cost to have him do it was pretty minimal when added on to a custom aluminum driveshaft and his CV axle kit install. The old 200SX dogleg shifted great but the bearings were getting...
by TheHeretic
08 Jun 2017 14:26
Forum: Project Builds
Topic: 2.3L of fun
Replies: 591
Views: 32782

Re: 2.3L of fun

What did Troy say about the fitment? I'm having him put in the CV's this week. Think he now uses a newer more improved set?

Go to advanced search