Search found 46 matches

by Tank510
12 Sep 2017 12:06
Forum: Classifieds
Topic: FS: BRE Front Lip
Replies: 0
Views: 181

FS: BRE Front Lip

Decided not to use it, in great condition. $120

IMG_0238.JPG
IMG_0238.JPG (168.84 KiB) Viewed 181 times
by Tank510
16 Jul 2017 12:47
Forum: Project Builds
Topic: Noob build
Replies: 51
Views: 3773

Re: Noob build

Well it's been a while, life got in the way. New job, still gotta move and bought a 240 project. But the 510 will be done first, no flipping back and forth. Assembled her a bit for transport, got it running decently well but sounds like a vacuum leak and bad timing so it sputters. Good enough to loa...
by Tank510
14 Jul 2017 18:45
Forum: Classifieds
Topic: FS: 13x6 mesh wheels
Replies: 0
Views: 208

FS: 13x6 mesh wheels

These came off the car when I first bought it, don't fit the 280ZX brakes and I don't have a use for them. Could look great with a little TLC. $160 obo - Tires are shot but two of them could be good for a few burnouts. https://vancouver.craigslist.ca/van/pts/6220035643.html iPhone 017.jpg iPhone 018...
by Tank510
14 Jul 2017 18:19
Forum: Classifieds
Topic: FS: 1971 510 2DR Seat Brackets
Replies: 1
Views: 267

FS: 1971 510 2DR Seat Brackets

These were cut out of a rust free car, all the spot welds drilled out. Would hate to throw them away if anyone needed them, 20 bucks a side + shipping if required.

iPhone 023.jpg
iPhone 023.jpg (150.52 KiB) Viewed 267 times
by Tank510
28 Jun 2017 15:55
Forum: Classifieds
Topic: Trunk Lid - Exc Cond - REDUCED AGAIN **
Replies: 4
Views: 726

Re: Trunk Lid - Exc Cond - REDUCED AGAIN **

How much to ship to V8N 2K2
by Tank510
04 May 2017 13:07
Forum: Classifieds
Topic: WTB: Heater Control Valve
Replies: 16
Views: 1276

Re: WTB: Heater Control Valve

You have a part number on that valve?
by Tank510
01 May 2017 11:28
Forum: Project Builds
Topic: Noob build
Replies: 51
Views: 3773

Re: Noob build

Well, it was time to do the exhaust. So I ended up deciding to ditch the cheap eBay pipe and bought a magnaflow 5" straight through muffler and a 3.5" tip. This should sound nice with the resonator that I kept from the original kit. I did the rear section first, tried to get as close to th...
by Tank510
24 Apr 2017 14:37
Forum: Engine Swap
Topic: SR/KA Mounts by Mckinney
Replies: 10
Views: 700

Re: SR/KA Mounts by Mckinney

Although I didn't do it myself, the mount can easily be flipped and all you need is the stock motor mounts. I did this on my KA build and it worked fine, to date there doesn't seem to be any excess vibrations etc but I've only ever ran it in my garage, not driving around. If you have a buddy that ca...
by Tank510
24 Apr 2017 13:16
Forum: Project Builds
Topic: Noob build
Replies: 51
Views: 3773

Re: Noob build

Well this weekend was good, the car now runs for more than 5 seconds after I got a different MAF. I used the MAF out of my neighbors old Auto 240SX, car runs and doesn't bog out after 5 sec. I plug my old MAF into his car, it runs fine. Now mine won't idle properly so it appears I might have a vacuu...
by Tank510
18 Apr 2017 17:00
Forum: Project Builds
Topic: 68 2-Door Restomod
Replies: 106
Views: 5223

Re: 68 2-Door Restomod

Awesome build!
by Tank510
04 Apr 2017 15:14
Forum: Project Builds
Topic: Noob build
Replies: 51
Views: 3773

Re: Noob build

As luck would have it the new ECU didn't show up till the day I left on vacation. It was probably better that way since the engine still only runs for 5 sec unless the MAF is disconnected or I rev the piss out of it. Made the decision to keep going, just rewire the mess at the front of the motor and...
by Tank510
13 Mar 2017 15:23
Forum: Project Builds
Topic: Noob build
Replies: 51
Views: 3773

Re: Noob build

So after a week of painful head scratching it FINALLY RUNS! Only for five seconds, then it dies, but that'll be dealt with later. A couple of problems I had: 1. Engine came without Ignition module - didn't realize it and when I sourced one I had spark. 2. Wiring diagram I used had the ECU BUP and E...

Go to advanced search