Search found 1060 matches

by Three B's Racing
18 Dec 2017 05:19
Forum: General & Technical
Topic: looking or the datsun bible.
Replies: 10
Views: 2149

Re: looking or the datsun bible.

It took 4 years for a "That's totally fine by me? Ray, you loose then find your Time Machines throttle stick? 8>)
by Three B's Racing
15 Dec 2017 05:07
Forum: Project Builds
Topic: Bert Vorgon's Spring Maintenance Project
Replies: 125
Views: 8871

Re: Bert Vorgon's Spring Maintenance Project

Hi Bert, Your trims are in much better condition than mine and the first piece that the staples go through are badly affected by ferrous oxide, must have come from a wetter area of ‘merica. As you say those staples are very tenacious and don’t let go easily. I think I’ll probably need to replace th...
by Three B's Racing
15 Dec 2017 05:04
Forum: Body & Electrical
Topic: Exterior squeegees.
Replies: 6
Views: 96

Re: Exterior squeegees.

I used 3M weather strip adhesive. I put a thin layer on both mating pieces and le it dry, then applied another thin layer and placed the rubber seal into position. But you must take caution and be precise in your placement because once that adhesive touches, it sticks and having to pull it back off ...
by Three B's Racing
15 Dec 2017 04:53
Forum: Suspension
Topic: Suspension and brake questions, I searched
Replies: 11
Views: 180

Re: Suspension and brake questions, I searched

Actually, the ZX springs will work. One of the guys "Vince" who attends the EastCoast 510 meet at Summit Point has stock ZX struts and springs. He had to remove metal around the entry of the strut tower but they fit. Only issue is any caster adjustment you may want to add is very limited. ...
by Three B's Racing
14 Dec 2017 05:06
Forum: Suspension
Topic: Front Sway Bar Help
Replies: 2
Views: 66

Re: Front Sway Bar Help

Is it possible you've recieved a swaybar for a SR motor install? Looking at your picture I see if the crossmember center section was reversed like it would be for the SR, the swaybar would easily clear. Putting the car on the ground would easily put your swaybar against the stock crossmember.
by Three B's Racing
12 Dec 2017 04:32
Forum: General Discussion
Topic: cross contamination destroying plastics?
Replies: 5
Views: 663

Re: cross contamination destroying plastics?

had a nos nissan windshield gasket fail over the weekend. the gasket was in its stock bag prior to installation back in may. only soap and water used during installation. the gasket failed along the top of the windscreen @ the pinch weld groove. could the 3m 777 spray adhesive used during headliner...
by Three B's Racing
11 Dec 2017 05:23
Forum: Project Builds
Topic: Another 72 510
Replies: 37
Views: 2551

Re: Another 72 510

No, no worries on the comment. This would be an inside story between Rob and Jason from a project many years back - not negative at all, but a good story to share in person. Why don’t you all attend the Christmas party this year and share it, Jason (and family, Rob and Greg. As Lou might say, this ...
by Three B's Racing
08 Dec 2017 06:44
Forum: Body & Electrical
Topic: Chinese made aftermarket windshields
Replies: 237
Views: 14739

Re: Chinese made aftermarket windshields

I have installed a Pilkington screen on one of my cars, and what I can say against the Chinese glass is that it is thicker and sits in the OEM rubber much better than the Chinese ones do and the Pilkington is closer to the OEM glass thickness. It’s still a bit thinner, but it’s a lot closer. As far...
by Three B's Racing
07 Dec 2017 05:29
Forum: Body & Electrical
Topic: Chinese made aftermarket windshields
Replies: 237
Views: 14739

Re: Chinese made aftermarket windshields

I've been running a Pro Source windshild since `97 and though it does have pits and one chip I chock that up to yearly runs to Summit Point WV since `99, Road Atlanta 2010, Canby 2017, North Carolina-Maryland runs just to see friends and typical New Hampshire, Massacheuttes, Maine and Vermont roads ...
by Three B's Racing
07 Dec 2017 05:04
Forum: General Discussion
Topic: New potential products for 510's and Datsun from Mattndew76
Replies: 609
Views: 41733

Re: New potential products for 510's and Datsun from Mattndew76

How would this S14 maniforld compair to the Getty S14 manifold in $$$ and flow?
by Three B's Racing
05 Dec 2017 06:48
Forum: Project Builds
Topic: Noob build
Replies: 73
Views: 5114

Re: Noob build

Sounds exactly like this stuff from Eastwood. It goes on like paint which allows it to seep into all those you want it to go places then dries to a self healing film.

anti-rust.jpg
anti-rust.jpg (182.07 KiB) Viewed 154 times
by Three B's Racing
04 Dec 2017 05:17
Forum: Project Builds
Topic: Noob build
Replies: 73
Views: 5114

Re: Noob build

Welding will simply bubble the POR-15 and expose raw metal for a fresh coast of rust. I'd recommend going back in through the back side and adding a fresh coat in those areas.
by Three B's Racing
04 Dec 2017 04:48
Forum: Introductions
Topic: I'm back! 71 510 4 door with 16,900 miles
Replies: 41
Views: 2372

Re: I'm back! 71 510 4 door with 16,900 miles

DonnieDatsun wrote:Nicest survivor east of the Mississippi, hands down.


Maybe! A close side to side comparison with Nathan Marshall's 510 would need to be performed first.
by Three B's Racing
01 Dec 2017 04:44
Forum: Suspension
Topic: How to: Rejuvenate Calipers and Hubs
Replies: 10
Views: 299

Re: How to: Rejuvenate Calipers and Hubs

Rebuilding the calipers is pretty straight forward, new seals, boot, piston, maybe sliders, degreasing, paint. One thing you need to know is removing the piston. Put a block of wood in front of the piston thick enough to leave about a 1" space. Remove zirk fitting and pressurize the the piston ...
by Three B's Racing
01 Dec 2017 04:35
Forum: Events
Topic: Mitty 2018
Replies: 5
Views: 206

Re: Mitty 2018

tcflacars wrote:Also wanted to know will there be a Datsun swap meet at the Mitty??????


I suppose if you were to bring a load of parts. The 2010 Mitty saw I believe just a couple of sites with parts. It's a crap shoot on that.

Go to advanced search