Search found 95 matches
- 03 Oct 2012 13:47
- Forum: Powertrain
- Topic: Can't get into gear without grinding
- Replies: 27
- Views: 5808
Re: Can't get into gear without grinding
I replaced the master cylinder on Sunday, bled the system, went back last night and bled it again for a long time and everything functions properly now. I took it for a drive this morning and it was still a bit sticky until the car warmed up, but I can get into every gear no problem now. The old mas...
- 26 Sep 2012 10:40
- Forum: Powertrain
- Topic: Can't get into gear without grinding
- Replies: 27
- Views: 5808
Re: Can't get into gear without grinding
I was just saying that I've bled it twice without getting air. I can bleed it again this weekend if y'all think it's going to make a difference... I double checked the measurements for pedal travel and play at the slave cylinder and both measurements are correct. I'll confirm that I'm not losing flu...
- 24 Sep 2012 10:54
- Forum: Powertrain
- Topic: Can't get into gear without grinding
- Replies: 27
- Views: 5808
Re: Can't get into gear without grinding
Hi technology, I know there has been no shortage of advice for you here. But I wanted to share a tip with you on bleeding hydraulic systems - brake or clutch. Press pedal down, then open bleeder. Close bleeder just as flow is stopping and then retract pedal. Any delay in closing the bleeder before ...
- 24 Sep 2012 04:26
- Forum: Powertrain
- Topic: Can't get into gear without grinding
- Replies: 27
- Views: 5808
Re: Can't get into gear without grinding
Sorry about not being specific enough, I'm still learning what's relevant information and what isn't.
- 23 Sep 2012 14:44
- Forum: Powertrain
- Topic: Can't get into gear without grinding
- Replies: 27
- Views: 5808
Re: Can't get into gear without grinding
I had been opening it, letting them pump the pedal a few times, closing it, checking that there was still fluid, repeat. Fill the reservoir and have some help keep it full and pump the clutch peddle for you. Open the bleeder on the slave. Usually fluid will begin to siphon down and out by itself alo...
- 22 Sep 2012 18:05
- Forum: Powertrain
- Topic: Can't get into gear without grinding
- Replies: 27
- Views: 5808
Re: Can't get into gear without grinding
I got all of the air out that normal bleeding will get out. Do you mean that there might be some trapped in the slave cylinder?
- 22 Sep 2012 15:18
- Forum: Powertrain
- Topic: Can't get into gear without grinding
- Replies: 27
- Views: 5808
Re: Can't get into gear without grinding
I just bled it and definitely got some bubbles, but I didn't gain much travel. I can get it into gear with less grinding now, sometimes with no grinding, but still clearly not how it should be. It's still barely breaking 3/4" of travel at the transmission.
- 22 Sep 2012 13:06
- Forum: Powertrain
- Topic: Can't get into gear without grinding
- Replies: 27
- Views: 5808
Re: Can't get into gear without grinding
Yeah...looks like I'm getting about 3/4" of travel at the transmission. So about half the travel that I should be getting.
So advice time: Replace the master or do master and slave just to be safe?
So advice time: Replace the master or do master and slave just to be safe?
- 18 Sep 2012 15:59
- Forum: Powertrain
- Topic: Can't get into gear without grinding
- Replies: 27
- Views: 5808
Re: Can't get into gear without grinding
I just moved here, so I haven't fully converted to metric yet :wink: There's plenty of fluid in the master cylinder reservoir. I'll make sure everything is tightened down when I get a chance. I figure bleeding it again won't hurt anything and could solve the problem. If it doesn't, I don't lose anyt...
- 18 Sep 2012 15:02
- Forum: Powertrain
- Topic: Can't get into gear without grinding
- Replies: 27
- Views: 5808
Re: Can't get into gear without grinding
How much should it move? Is there a good way to measure or estimate? Looking at the lever that the slave cylinder moves and the opening that allows for it to move, I would guess that it's not moving as far as it should.
- 18 Sep 2012 13:00
- Forum: Powertrain
- Topic: Can't get into gear without grinding
- Replies: 27
- Views: 5808
Re: Can't get into gear without grinding
Oh, sorry, that wasn't very clear. It was bled when the slave cylinder was replaced. I meant I hadn't tried bleeding it again.
- 18 Sep 2012 10:39
- Forum: Powertrain
- Topic: Can't get into gear without grinding
- Replies: 27
- Views: 5808
Can't get into gear without grinding
I recently replaced my clutch slave cylinder and everything has been fine until about a week ago when I suddenly can't get into gear without majorly grinding. If the engine is off, everything is fine. I can get into any gear. But once the engine is running I just grind any time I try to get in gear....
- 22 Aug 2012 17:08
- Forum: 510 Club of BC
- Topic: what insurance do you guys use?
- Replies: 16
- Views: 10671
Re: what insurance do you guys use?
The ICBC website makes it sound like you can only get this if you have more than $5000 of equipment...
http://www.icbc.com/autoplan/optional/v ... -equipment
I'll have to dig through the receipts that came with the car to see what I have documented.
http://www.icbc.com/autoplan/optional/v ... -equipment
I'll have to dig through the receipts that came with the car to see what I have documented.
- 10 Aug 2012 08:25
- Forum: Body & Electrical
- Topic: Quick (hopefully) alternator wiring question
- Replies: 23
- Views: 5815
Re: Quick (hopefully) alternator wiring question
280ZX = Hitachi Alternator Type LR160What's the advantage of this over the 280ZX alternator that I got? I haven't done anything with it yet, so I can always return it.
- 09 Aug 2012 14:27
- Forum: Body & Electrical
- Topic: Quick (hopefully) alternator wiring question
- Replies: 23
- Views: 5815
Re: Quick (hopefully) alternator wiring question
Ok, I have everything I need other than the fusible link. I've read that you either want 2 or 4 sizes down from the wiring that you're protecting, so 12 or 14 gauge link for my 10 gauge wires. I also read that the length of the fusible link matters. How do I determine how much to use or does it actu...