Page 110 of 114

Re: What did you do on your 510 today?

Posted: 10 Dec 2018 12:46
by eastbaysolo_73
greenthumb wrote:
09 Dec 2018 21:36
Looks fantastic! Those dapper lights have the halo or angel eyes effect?
Thanks Greenthumb they do have have the halo rings.

Re: What did you do on your 510 today?

Posted: 17 Dec 2018 14:16
by eastbaysolo_73
finally got the car off the jack stands this weekend. It still needs to have some suspension adjustments. But good enough for now.
Imagenomorejacks by v p, on Flickr

Re: What did you do on your 510 today?

Posted: 18 Dec 2018 21:30
by jefe de jefes
eastbaysolo_73 wrote:
09 Dec 2018 19:48
Mounted the rear cross member today and rear coils. Need the car on the ground to make room for my wife's car.
Put on the rear wheels as well. I need to set the ride hight once I get the front suspension buttoned up and wheels installed.

ImageRearcoil by v p, on Flickr


Imagerearwheel by v p, on Flickr


Where’d you get the qa1’s?

Re: What did you do on your 510 today?

Posted: 19 Dec 2018 07:31
by drawks
eastbaysolo_73 wrote:
17 Dec 2018 14:16
finally got the car off the jack stands this weekend. It still needs to have some suspension adjustments. But good enough for now.
Imagenomorejacks by v p, on Flickr
Those mesh wheels look dope! I had some enkei 92 meshies on my first dime back in '95

Re: What did you do on your 510 today?

Posted: 19 Dec 2018 11:27
by eastbaysolo_73
jefe de jefes wrote:
18 Dec 2018 21:30
eastbaysolo_73 wrote:
09 Dec 2018 19:48
Mounted the rear cross member today and rear coils. Need the car on the ground to make room for my wife's car.
Put on the rear wheels as well. I need to set the ride hight once I get the front suspension buttoned up and wheels installed.

ImageRearcoil by v p, on Flickr


Imagerearwheel by v p, on Flickr


Where’d you get the qa1’s?
Got them from here at DPracing.
http://www.dpracing.co

Re: What did you do on your 510 today?

Posted: 19 Dec 2018 11:32
by eastbaysolo_73
drawks wrote:
19 Dec 2018 07:31
eastbaysolo_73 wrote:
17 Dec 2018 14:16
finally got the car off the jack stands this weekend. It still needs to have some suspension adjustments. But good enough for now.
Imagenomorejacks by v p, on Flickr
Those mesh wheels look dope! I had some enkei 92 meshies on my first dime back in '95
Nice! These wheels are 3 piece AME wheels, which are actually made by Enkei. They were only offered in Japan as there luxury brand.

Re: What did you do on your 510 today?

Posted: 19 Dec 2018 13:32
by jefe de jefes
eastbaysolo_73 wrote:
19 Dec 2018 11:27
jefe de jefes wrote:
18 Dec 2018 21:30
eastbaysolo_73 wrote:
09 Dec 2018 19:48
Mounted the rear cross member today and rear coils. Need the car on the ground to make room for my wife's car.
Put on the rear wheels as well. I need to set the ride hight once I get the front suspension buttoned up and wheels installed.

ImageRearcoil by v p, on Flickr


Imagerearwheel by v p, on Flickr


Where’d you get the qa1’s?
Got them from here at DPracing.
http://www.dpracing.co
Thanks man

Re: What did you do on your 510 today?

Posted: 08 Jan 2019 13:05
by KiKiIchiBan
Not today, but I have finally primed my engine.

https://www.youtube.com/watch?v=wRZHzYc9NhI

I did try to start it, but it didn't fire up, I think there is something wrong with the coil, or with my knowledge, couldn't get a spark either way.

Re: What did you do on your 510 today?

Posted: 08 Jan 2019 17:41
by bertvorgon
Unlike our poor compatriot above me, my car started on the 2nd crank, which surprised the hell out of me, it was 39F (4C) in the garage. My new storage garage, not that I'm complaining, has the attic hatch right above my car. So, when my daughter or son-in-law need to remove anything, or, in this case put the Christmas decorations away, I need to move the car. At that point I then need to let it run and bring it up to 200F. to eliminate any water/condensation.

As I have no choke I just let the float bowl fill up, give the throttle a 1/2 dozen good blips, to get the accelerator pump dumping a good slug of fuel in there, let it sit for 30 seconds to try to evaporate in the cold, then hit the starter. Wham, it virtually lit off with two cranks. I cycle all the relays, fan to high, wipers, lights, just to keep things moving. After 15 minutes slide the car back into it's slot and now can be good till spring.

I did remove the glove box, for a small project which I will start a thread on in case anyone is interested

Re: What did you do on your 510 today?

Posted: 13 Jan 2019 00:27
by Tedman
Installing a remote oil filter mount. Last week I got the filter mounted on the strut tower with the Traco mount. Today I installed the BRE remote filter block adapter and assembled the oil return hose.

Image

Re: What did you do on your 510 today?

Posted: 15 Jan 2019 13:28
by two_68_510s
AN 6?

Re: What did you do on your 510 today?

Posted: 20 Jan 2019 21:54
by Tedman
two_68_510s wrote:
15 Jan 2019 13:28
AN 6?
AN -10

Re: What did you do on your 510 today?

Posted: 10 Feb 2019 08:50
by KiKiIchiBan
I started mine up for the first time :)

Re: What did you do on your 510 today?

Posted: 06 Mar 2019 07:04
by cartel
Bolted on new wheels... New vto installed. Over inch clearance to wheelwell on rear and about 3/16 to control arm.. I think with a modified arm 225s will fit..


Image

Re: What did you do on your 510 today?

Posted: 07 Mar 2019 11:20
by iceman510
More details please.

Wheel size and offset?

Tire size?