SR20DET wiring into 510

New posts disabled. Archived technical discussion about the Datsun PL510
Crevier
Posts: 143
Joined: 06 Apr 2007 19:42

Postby Crevier » 18 Apr 2007 13:54

yeah your ''artist skill'' sucks big time lol

thanks alot again, everyone who help!

sticky???

User avatar
icehouse
Posts: 2995
Joined: 17 Jul 2005 17:06
Location: Everett Wa

Postby icehouse » 18 Apr 2007 21:09

As long as someone re draws my "wiring diagram" :D
I liked Hainz better...... Can we trade back?

Crevier
Posts: 143
Joined: 06 Apr 2007 19:42

Postby Crevier » 18 Apr 2007 21:27

ok ok I wil redraw your diagram! and sticky it!

SMITHENGINEERED
Posts: 253
Joined: 10 Jan 2007 12:35
Location: Louisville, Kentucky

Postby SMITHENGINEERED » 19 Apr 2007 16:06

Crevier wrote:ok ok I wil redraw your diagram! and sticky it!


Thanks Guys :D

User avatar
Yellowcar
Posts: 1204
Joined: 19 Apr 2004 15:22
Location: Redmond, WA

Postby Yellowcar » 20 Apr 2007 08:35

Anybody got a diagram for a 91 KA24DE?

Thanks

arkitekz
Supporter
Posts: 347
Joined: 15 Jul 2004 22:39
Location: San Diego, CA

Postby arkitekz » 20 Apr 2007 09:09

Yellowcar wrote:Anybody got a diagram for a 91 KA24DE?

Thanks


Yeah! Diagram form ka24de 91-93 would be the icing on the cake.

User avatar
oregondime
Posts: 198
Joined: 06 Jan 2007 12:45
Location: san antonio, tx

Postby oregondime » 20 Apr 2007 09:40

here you go, its the pinout guide for every motor japanese and ka: http://www.az240sx.org/tech/Pinout/ that link took me 2 hours to find before :)

User avatar
510-Trevor
Supporter
Posts: 1362
Joined: 03 Mar 2007 18:34
Location: Calgary, Alberta

REDRAWN DIAGRAM

Postby 510-Trevor » 20 Apr 2007 22:38

icehouse - here is your diagram all cleaned up.

If anyone has any changes/additions they think should be added, post them here. If there is a consensus then I will revise the drawing as required.

Thanks.

See revised sketch below.
Last edited by 510-Trevor on 21 Apr 2007 10:28, edited 1 time in total.
1972 Yellow 4dr - 1972 Red 2dr

Crevier
Posts: 143
Joined: 06 Apr 2007 19:42

RE: REDRAWN DIAGRAM

Postby Crevier » 21 Apr 2007 06:21

the picture doesn't work

SMITHENGINEERED
Posts: 253
Joined: 10 Jan 2007 12:35
Location: Louisville, Kentucky

Postby SMITHENGINEERED » 21 Apr 2007 08:20

Good Work 510-Trevor much appreciated!

:D

User avatar
510-Trevor
Supporter
Posts: 1362
Joined: 03 Mar 2007 18:34
Location: Calgary, Alberta

Postby 510-Trevor » 21 Apr 2007 08:42

you need to click on the word 'download' . This will open the pdf file for viewiing.
1972 Yellow 4dr - 1972 Red 2dr

Crevier
Posts: 143
Joined: 06 Apr 2007 19:42

Postby Crevier » 21 Apr 2007 09:16

the switch you draw isn't ''switch'' it is a relay, modify it to like my diagram symbol with correct wire to coil and contact

I say this for someone who will look at your diagram and put switch and not relay

and everything else is very good!

thanks!

User avatar
510-Trevor
Supporter
Posts: 1362
Joined: 03 Mar 2007 18:34
Location: Calgary, Alberta

REVISED DIAGRAM

Postby 510-Trevor » 21 Apr 2007 16:31

Here is the revised diagram.

Perhaps someone can come up with better wording for the disclaimer at the bottom of the page.
Attachments
sr20det wiring diag.pdf
sr to 510 harness diagram
(49.47 KiB) Downloaded 450 times
1972 Yellow 4dr - 1972 Red 2dr

User avatar
Baz
Posts: 508
Joined: 13 Jul 2004 07:34
Location: Lonsdale South OZ

RE: REVISED DIAGRAM

Postby Baz » 21 Apr 2007 20:49

one small thing that is overlooked when wiring up an Sr is the alternator warning lamp.
solder a 100 ohm resistor across the lamp terminals. this can prevent alternator failure if the warning lamp blows.
Fuel pump is best triggered from the ecu as this will cut the pump in the event of an accident where the engine stops & the driver is unable to cut the ign.
Most after market tachs will require a pull up resistor ( about 5K) across the power/signal wire.
With early ign switches bridging the ballast bypass wire to the main ign on will do the trick.
The white 3mm sense wire on the alterator is best trigged by the ign on relay. can prevent battery going flat.
If using the original temp gauge with the SR temp sender the gauge will need recalibrating, best to replace the votage reg at the same time with a solid state unit.

doughboi916
Posts: 73
Joined: 12 Jun 2006 12:02

RE: REVISED DIAGRAM

Postby doughboi916 » 22 Apr 2007 10:27

will a 91 ka wire up like this? anyone want to help me with a diagram also, i would appreciate it.


Return to “Technical - Archive”



Who is online

Users browsing this forum: No registered users and 3 guests