SR20DET wiring into 510

New posts disabled. Archived technical discussion about the Datsun PL510
Crevier
Posts: 143
Joined: 06 Apr 2007 19:42

Post by Crevier »

yeah your ''artist skill'' sucks big time lol

thanks alot again, everyone who help!

sticky???
User avatar
icehouse
Posts: 3885
Joined: 17 Jul 2005 17:06
Location: Everett Wa

Post by icehouse »

As long as someone re draws my "wiring diagram" :D
"People don't like it when shit doesn't match their rule of thumb." Sam
Crevier
Posts: 143
Joined: 06 Apr 2007 19:42

Post by Crevier »

ok ok I wil redraw your diagram! and sticky it!
SMITHENGINEERED
Posts: 253
Joined: 10 Jan 2007 12:35
Location: Louisville, Kentucky

Post by SMITHENGINEERED »

Crevier wrote:ok ok I wil redraw your diagram! and sticky it!
Thanks Guys :D
User avatar
Yellowcar
Posts: 1204
Joined: 19 Apr 2004 15:22
Location: Redmond, WA

Post by Yellowcar »

Anybody got a diagram for a 91 KA24DE?

Thanks
arkitekz
Supporter
Posts: 347
Joined: 15 Jul 2004 22:39
Location: San Diego, CA

Post by arkitekz »

Yellowcar wrote:Anybody got a diagram for a 91 KA24DE?

Thanks
Yeah! Diagram form ka24de 91-93 would be the icing on the cake.
User avatar
oregondime
Posts: 198
Joined: 06 Jan 2007 12:45
Location: san antonio, tx

Post by oregondime »

here you go, its the pinout guide for every motor japanese and ka: http://www.az240sx.org/tech/Pinout/ that link took me 2 hours to find before :)
User avatar
510-Trevor
Supporter
Posts: 1373
Joined: 03 Mar 2007 18:34
Location: Calgary, Alberta

REDRAWN DIAGRAM

Post by 510-Trevor »

icehouse - here is your diagram all cleaned up.

If anyone has any changes/additions they think should be added, post them here. If there is a consensus then I will revise the drawing as required.

Thanks.

See revised sketch below.
Last edited by 510-Trevor on 21 Apr 2007 10:28, edited 1 time in total.
1972 Yellow 4dr
Crevier
Posts: 143
Joined: 06 Apr 2007 19:42

RE: REDRAWN DIAGRAM

Post by Crevier »

the picture doesn't work
SMITHENGINEERED
Posts: 253
Joined: 10 Jan 2007 12:35
Location: Louisville, Kentucky

Post by SMITHENGINEERED »

Good Work 510-Trevor much appreciated!

:D
User avatar
510-Trevor
Supporter
Posts: 1373
Joined: 03 Mar 2007 18:34
Location: Calgary, Alberta

Post by 510-Trevor »

you need to click on the word 'download' . This will open the pdf file for viewiing.
1972 Yellow 4dr
Crevier
Posts: 143
Joined: 06 Apr 2007 19:42

Post by Crevier »

the switch you draw isn't ''switch'' it is a relay, modify it to like my diagram symbol with correct wire to coil and contact

I say this for someone who will look at your diagram and put switch and not relay

and everything else is very good!

thanks!
User avatar
510-Trevor
Supporter
Posts: 1373
Joined: 03 Mar 2007 18:34
Location: Calgary, Alberta

REVISED DIAGRAM

Post by 510-Trevor »

Here is the revised diagram.

Perhaps someone can come up with better wording for the disclaimer at the bottom of the page.
Attachments
sr20det wiring diag.pdf
sr to 510 harness diagram
(49.47 KiB) Downloaded 807 times
1972 Yellow 4dr
User avatar
Baz
Posts: 521
Joined: 13 Jul 2004 07:34
Location: Lonsdale South OZ

RE: REVISED DIAGRAM

Post by Baz »

one small thing that is overlooked when wiring up an Sr is the alternator warning lamp.
solder a 100 ohm resistor across the lamp terminals. this can prevent alternator failure if the warning lamp blows.
Fuel pump is best triggered from the ecu as this will cut the pump in the event of an accident where the engine stops & the driver is unable to cut the ign.
Most after market tachs will require a pull up resistor ( about 5K) across the power/signal wire.
With early ign switches bridging the ballast bypass wire to the main ign on will do the trick.
The white 3mm sense wire on the alterator is best trigged by the ign on relay. can prevent battery going flat.
If using the original temp gauge with the SR temp sender the gauge will need recalibrating, best to replace the votage reg at the same time with a solid state unit.
doughboi916
Posts: 73
Joined: 12 Jun 2006 12:02

RE: REVISED DIAGRAM

Post by doughboi916 »

will a 91 ka wire up like this? anyone want to help me with a diagram also, i would appreciate it.
Post Reply