what is the thread size and pitch for a stub axle
-
- Posts: 652
- Joined: 09 Aug 2004 18:26
- Location: tigard oregon
what is the thread size and pitch for a stub axle
what is the thread size and pitch for a rear stub axle i was changing my rear wheel bearings and messed the threads up
L series only have one header!
i need another garage mine is full of part's
i need another garage mine is full of part's
Re: what is the thread size and pitch for a stub axle
damn....if I were home I could tell you, I just took my stub axle into the hardware store in Japan and found the right size die. it wasn't cheap though...
Re: what is the thread size and pitch for a stub axle
it's the same as the zx if that helps
"People don't like it when shit doesn't match their rule of thumb." Sam
Re: what is the thread size and pitch for a stub axle
It's pretty easy to measure, even with a ruler. It is going to be some sort of semi standard metric size, so find the diameter to the closest mm and then count how many threads there are in 10mm of length, and then divide 10 by that number to get the mm per thread(which will likely be a multiple of 1/4s of a mm). You'll come up with something like this:
Measure 18mm diameter,
count 8 threads in 10mm,
10/8 = 1.25
thread is M18x1.25
Measure 18mm diameter,
count 8 threads in 10mm,
10/8 = 1.25
thread is M18x1.25
-
- Posts: 652
- Joined: 09 Aug 2004 18:26
- Location: tigard oregon
Re: what is the thread size and pitch for a stub axle
thank you
L series only have one header!
i need another garage mine is full of part's
i need another garage mine is full of part's
Re: what is the thread size and pitch for a stub axle
this is just an example, not the answer you are looking for.Derek wrote:... something like this:
Measure 18mm diameter,
count 8 threads in 10mm,
10/8 = 1.25
thread is M18x1.25
richard norrish
'68 'goon resto / '71 ice racer / '72 'goon project / '70 4-door rust pile / '67 520 project
----------------------------------------------------------------------
'68 'goon resto / '71 ice racer / '72 'goon project / '70 4-door rust pile / '67 520 project
----------------------------------------------------------------------
shardik wrote: My swap will be made of solid gold and it will run on puppy farts.
Re: what is the thread size and pitch for a stub axle
I'll be home tomorrow and will look in my tool box and let you know what the die size is......stay tuned!
Re: what is the thread size and pitch for a stub axle
Oops -- did I not make that clear?rnorrish wrote:this is just an example, not the answer you are looking for.Derek wrote:... something like this:
Measure 18mm diameter,
count 8 threads in 10mm,
10/8 = 1.25
thread is M18x1.25
Re: what is the thread size and pitch for a stub axle
Derek,
The funny thing is that I think you were really close. I believe it's an M20 X 1.5 thread, but we'll wait for goichi's confirmation on that
Byron
The funny thing is that I think you were really close. I believe it's an M20 X 1.5 thread, but we'll wait for goichi's confirmation on that
Byron
Love people and use things,
because the opposite never works.
because the opposite never works.
-
- Posts: 652
- Joined: 09 Aug 2004 18:26
- Location: tigard oregon
Re: what is the thread size and pitch for a stub axle
you sir are correct
and i knew it was an example
and i knew it was an example
L series only have one header!
i need another garage mine is full of part's
i need another garage mine is full of part's
Re: what is the thread size and pitch for a stub axle
yeap, 20m 1.5 pitch. I just looked at the die I that I used from mine.
Re: what is the thread size and pitch for a stub axle
Geez, that 'ole grey matter still retains stuff once in a while!!
Byron
Byron
Love people and use things,
because the opposite never works.
because the opposite never works.
-
- Posts: 275
- Joined: 06 Dec 2005 15:26
Re: what is the thread size and pitch for a stub axle
I did the same exact thing on my car when I was pulling the drum backing plates off. I thought I had screwed the pooch for sure, I couldn't get the nut to start threading on at all - probably because I had used a BIG hammer instead of a press to remove the stub axles (oops!). I took it to a local machine shop and they recommended I use a thread file. Sure enough it worked great and only took a few minutes, I'm embarassed to say that my thread file is one of my favorite tools (I make a lot of mistakes) LOL.
Give the thread file a try if you like, they're cheap and it worked great for me.
Give the thread file a try if you like, they're cheap and it worked great for me.