Project 635 - 300HP RWD 620

View and post your Nissan/Datsun project(s)
User avatar
Edm620
Posts: 85
Joined: 06 Dec 2017 20:44
Location: Edmonton

Re: Project 635 - 300HP RWD 620

Post by Edm620 » 18 Aug 2020 14:41

Nice to see your progress on 635
"If you don't know where you're going, any road will take you there"
Ugandan Proverb

User avatar
Edm620
Posts: 85
Joined: 06 Dec 2017 20:44
Location: Edmonton

Re: Project 635 - 300HP RWD 620

Post by Edm620 » 19 Aug 2020 07:22

Are you posting on Ratsun as well? I think lots of guys would follow your build there, site is more active on truck builds.
"If you don't know where you're going, any road will take you there"
Ugandan Proverb

User avatar
DADZSUN
Supporter
Posts: 465
Joined: 08 Aug 2011 18:35
Location: Ottawa, ON

Re: Project 635 - 300HP RWD 620

Post by DADZSUN » 19 Aug 2020 07:30

Edm620 wrote:
19 Aug 2020 07:22
Are you posting on Ratsun as well? I think lots of guys would follow your build there, site is more active on truck builds.
Not yet. I wanted a quieter environment to post updates as I work my way through it first.

Once I get a few more critical items sorted out and installed, and the truck is actually running, then I'll post a more condensed how-to thread on Ratsun.
'72 Datsun 510 - MS KA24e, Watanabes, STI R180 w/CV axles, R&P assisted steering
'76 Datsun 620 - VQ35DE, CD009, G35 suspension & brakes.
'76 Datsun 280z - 2021 Datsun Restomods R&D project
Creativity outlet: www.datsunrestomods.com

User avatar
DADZSUN
Supporter
Posts: 465
Joined: 08 Aug 2011 18:35
Location: Ottawa, ON

August update #3

Post by DADZSUN » 31 Aug 2020 17:36

More great progress on 635. Unfortunately this meant (once again), that a few steps backwards were required to go forward.

Frame.jpg
Frame.jpg (91.64 KiB) Viewed 261 times

There is an order of operations when building from scratch, and while I've been quite good and predicting most of it, there has been a few fumbles. I like to think that it still provided valuable information on clearance etc...

While I spent quite a bit of time finalizing/welding the front cross member, the biggest visible update is the addition of a driveshaft.

Driveshaft.jpg
Driveshaft.jpg (66.98 KiB) Viewed 261 times

Ottawa Driveshaft set me up with a brand new CD009 yoke, R200 flange, and 3.5" diameter driveshaft.

Exhaust.jpg
Exhaust.jpg (84.24 KiB) Viewed 261 times

Next up was routing the exhaust aft of the twin high-flow cats. It became obvious that for a cleaner & more direct exhaust, I needed to remove the completed transmission mount and lower it.

TrannyMount.jpg
TrannyMount.jpg (151.29 KiB) Viewed 261 times

Here's a pic of the finished V1 of the exhaust. Both banks had flexpipes added then flowed into a stock 'high-flow' Y pipe. After the merge, the exhaust dropped to the lowest point of the truck, 8.5" clearance.

ExhaustSetupOld.jpg
ExhaustSetupOld.jpg (128.94 KiB) Viewed 261 times

Unfortunately it became apparent that there was now no room for a cross beam. I needed this beam to 1) replace the stock structural unit that was cut out and, 2) provide a mount for front of the 720 fuel tank.

ExhaustSetupNew.jpg
ExhaustSetupNew.jpg (155.29 KiB) Viewed 261 times

V2 came next where each bank was first dropped then later merged. You can see the 3"x2" cross beam being test fitted.

FrameLatest.jpg
FrameLatest.jpg (154.75 KiB) Viewed 261 times

Here's the latest setup. The fuel tank is now fastened. The front bolts to a bracket on the aforementioned crossbeam, and the rear hangs off a 3"x1" cross beam which also provides a battery mount on the driver's side.

I'm close to being finished with these items. The crossbeams needs a few more gussets, cleaning, seam sealing and paint. The exhaust still need hangers, cleaning and paint.

Next, I'll be heavily reworking the fuel tank for a baffled fuel pump setup, a new modern sender, and brand new braided lines/filters.

Slowly, but surely, I'm getting through my 'To-do' list. I'm still well on track to fire up the VQ by end of month. I'm hoping for final assembly by early winter and on the road for DD/weekend duties by early April.
'72 Datsun 510 - MS KA24e, Watanabes, STI R180 w/CV axles, R&P assisted steering
'76 Datsun 620 - VQ35DE, CD009, G35 suspension & brakes.
'76 Datsun 280z - 2021 Datsun Restomods R&D project
Creativity outlet: www.datsunrestomods.com

User avatar
DADZSUN
Supporter
Posts: 465
Joined: 08 Aug 2011 18:35
Location: Ottawa, ON

Long bed goes bobtail

Post by DADZSUN » 15 Sep 2020 19:57

A couple aesthetic updates.

First up, I acquired a set of RX-7 3rd generation 'FD' wheels, 16x8 ET50. Yes, modification were required to clear the upgraded (to 2006 spec) front 320mm 2006 G35 rotors and caliper, and the front suspension upright needed a mm or two shave. :oops: Regardless, I'm stocked about these rims.
  • At just 15 lbs (for the reinforced version), they're very light. With crappy tires they're still 15lbs lighter than the OEM G35 7 spoke wheel and tire,
  • they have the high offset I need to combat the G35's extra 5" wider track,
  • they are are strong,
  • have a great simplistic look,
  • are authentic JDM,
  • they're CHEAP ($250Cdn)!
  • they're a nice homage to my past love, a Montego blue base FD, production #79 (in the world!) built in Dec '91. I loved that car (12.86 @114.5 MPH on street tires and gas, back in 1993), but didn't like the shitty reliability so much...


On to the second change. While I appreciate the +10" extended wheelbase on my 620 'long bed', one aesthetic consequence is the extra long bed, which IMO, creates a disproportionate rear overhang. This past week I finally got around to addressing that.

BikeFitment.jpg
BikeFitment.jpg (100.83 KiB) Viewed 124 times

The first step was to ensure my mountain bike would still fit nicely in the shortened bed. Measurements were made, double checked, and the cut was done.

CutBed.jpg
CutBed.jpg (114.11 KiB) Viewed 124 times

It didn't take long to make that first cut and I followed a structural bar underneath so it was fairly straight.

Pieces.jpg
Pieces.jpg (135.23 KiB) Viewed 124 times

Once the tailgate and 'extra' bed was cut, I proceeded to make a second cut and remove 9.25" from the rear of the bed.

Fitment.jpg
Fitment.jpg (112.36 KiB) Viewed 124 times

I cut the rear tailgate off in a manner that retained the lower skirts. I then cut a slit near the rear (small arrow) so that the lower skirt could be angled down (large arrow) to pickup the lower body line running along the length of the bed.

Another variable I had to deal with was that the rear of the bed actually tapers, resulting in a 1/2" variance. To rectify this I cut a few inches of the lower wall from floor (small arrow), thereby allowing the walls to be slightly angled in 1/4" per side to smoothly meet the tailgate walls.

RibbedBed.jpg
RibbedBed.jpg (132.3 KiB) Viewed 124 times

Next, the bed's ribs needed to taper down to smoothly meet the tailgate (so as not to catch cargo as it's getting pushed into the bed). I cut small wedge off each side of each rib and then hammered them down to meet the tailgate. Welds in this pic have yet to be cleaned obviously.

TaperedRibs.jpg
TaperedRibs.jpg (143.21 KiB) Viewed 124 times

Overall profile is MUCH better IMO. Also, the bed's new length is still long enough that the 5th side hook (unique to long beds) doesn't look out of place.

BobTailRear.jpg
BobTailRear.jpg (114.18 KiB) Viewed 124 times
BobtailSide.jpg
BobtailSide.jpg (62.49 KiB) Viewed 124 times

Up next I address the fuel tank to fire up the VQ. My son has been helping with bodywork which is awesome.

SandingRoof1.jpg
SandingRoof1.jpg (72.86 KiB) Viewed 124 times

Being a daily ride, I don't plan for this to be a show piece so just the large dents are being addressed followed by the stock orange/red single stage paint.

SandingRoof2.jpg
SandingRoof2.jpg (79.58 KiB) Viewed 124 times
Last edited by DADZSUN on 15 Sep 2020 20:45, edited 9 times in total.
'72 Datsun 510 - MS KA24e, Watanabes, STI R180 w/CV axles, R&P assisted steering
'76 Datsun 620 - VQ35DE, CD009, G35 suspension & brakes.
'76 Datsun 280z - 2021 Datsun Restomods R&D project
Creativity outlet: www.datsunrestomods.com

greenthumb
Posts: 230
Joined: 19 May 2013 20:57
Location: Langley, BC

Re: Project 635 - 300HP RWD 620

Post by greenthumb » 15 Sep 2020 20:33

Looks great to my eye. I agree, I always thought my long bed 620 looked a little awkward

Post Reply