71 1200 Project ( Picture intense)

View and post your Nissan/Datsun project(s)
powerbench
Posts: 63
Joined: 17 Dec 2016 12:43
Location: Surrey, B.C

71 1200 Project ( Picture intense)

Post by powerbench »

A couple years ago I bought a 71 1200 from a guy in Oregon. I had been looking for a few years , to replace a car I had when I was a kid. My original car in 86 was rough , but I loved that heap. Somebody stole the car twice in one day .Ultimately, the second theft they pretty much destroyed the car and got everything I owned. Fast forward 24 years later I found a car on the web and decided to buy it .....Loaded up the truck , grabbed a trailer and off I went.
Image

Image

Image
Last edited by powerbench on 18 Dec 2016 11:50, edited 1 time in total.
powerbench
Posts: 63
Joined: 17 Dec 2016 12:43
Location: Surrey, B.C

Re: 71 1200 Project

Post by powerbench »

After I bought the car , I pretty much parked it and left it for 2 years. ( work and life were very busy) and I didn't have the time to dedicate to the car.
I had a few things work out , and had been putting a little money away to at least get started on the car, so I grabbed the car and went in for a good inspection of what it needed......It needed alot. What I thought was a pretty much rust free car with no damage, turned out to not be ( I know Datsun...no such thing) .
I got a new rad support section and contacted Tycot1 to see if he could get her fixed up for me . ( That work was a little out of my skill set) Off the car went to Big Time Motors for a little surgery. When the car was there ,Tyson showed me some questionable repairs ......none of which I had even noticed. I had Tyson and his guy work their magic on what they could ( and what my wallet could handle) and figured I always wanted to up my skills on doing a complete car body wise. (Again thanks for all the Help Tyson and Doug)
So here comes the work.
Image
Image
Image
Image
Image
powerbench
Posts: 63
Joined: 17 Dec 2016 12:43
Location: Surrey, B.C

Re: 71 1200 Project

Post by powerbench »

Image
Image

Image

Image
Image
Image

Image
Image

Image

Image

Image
powerbench
Posts: 63
Joined: 17 Dec 2016 12:43
Location: Surrey, B.C

Re: 71 1200 Project

Post by powerbench »

So I got the car home and started dealing with my "rust free floors" and cleaning up my trunk area.
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
powerbench
Posts: 63
Joined: 17 Dec 2016 12:43
Location: Surrey, B.C

Re: 71 1200 Project ( Picture intense)

Post by powerbench »

Image

In went some new suspension....All new ,and some T3 coil overs


Image
Image
Image
Image

Image
16Again
Posts: 34
Joined: 09 Aug 2016 10:41
Location: Chilliwack BC.

Re: 71 1200 Project ( Picture intense)

Post by 16Again »

Looking good. Don't see many of those around any more.
powerbench
Posts: 63
Joined: 17 Dec 2016 12:43
Location: Surrey, B.C

Re: 71 1200 Project ( Picture intense)

Post by powerbench »

So I came into a few parts for the car and got to work doing some of the body work it needed . After the floors , I went onto the roof and the front end sheet metal. It was a good call on Tyson's part , because the car had been prepped very badly and I landed up having to rust mort the entire roof and fix alot of small dents.

Image
Image

Image

Image
Image
Image
Image
Last edited by powerbench on 19 Dec 2016 12:44, edited 1 time in total.
powerbench
Posts: 63
Joined: 17 Dec 2016 12:43
Location: Surrey, B.C

Re: 71 1200 Project ( Picture intense)

Post by powerbench »

So i stripped my trunk lid and fixed all the hand dents( shrink and stud pull as much as I could on a beer can and block the crap out of it..
I also scuffed and primed m.y fenders and lower valence. I also painted the inners on the fender.
Image
Image
Image
Image
Image
Image
Image
greenthumb
Posts: 261
Joined: 19 May 2013 20:57
Location: Langley, BC

Re: 71 1200 Project ( Picture intense)

Post by greenthumb »

can you elaborate a little on
'( shrink and stud pull as much as I could on a beer can and block the crap out of it..'
for us bodywork challenged types
Project looks great- whats the plan for power? Stock or a transplant?
powerbench
Posts: 63
Joined: 17 Dec 2016 12:43
Location: Surrey, B.C

Re: 71 1200 Project ( Picture intense)

Post by powerbench »

Ya , I m still learning the body work thing as well. A stud is a small stud you weld with a special welding gun and has a puller you attach to the stud . The same gun has a flat faced adapter that you use to apply heat to a specific area, to shrink the metal. Some guys use a torch to apply heat to an area to heat the metal and then quench it with water . It pulls the metal tight and stops that "oil can" effect after working the metal.....
The stud, is like the old way of drilling a hole and then threading a slide hammer into the dent , except you are not left with a hole to fill..
powerbench
Posts: 63
Joined: 17 Dec 2016 12:43
Location: Surrey, B.C

Re: 71 1200 Project ( Picture intense)

Post by powerbench »

As far as the drive train. I have a fairly recent rebuilt a12 with bigger pistons. I'm going to do a back yard port and polish on a spare head I have , and see if i can get the seats cut to fit bigger a14 valves.( and some other things ) Lynx side draft intake with a single 40 DCOE and header. 5spd ...nothing to exciting , but sort of quick and cheap for now....
powerbench
Posts: 63
Joined: 17 Dec 2016 12:43
Location: Surrey, B.C

Re: 71 1200 Project ( Picture intense)

Post by powerbench »

As the story continues. I got cracking on the back half of the car...( looking for rust and repairing any dents I could with out going crazy)
I stripped the back of the car and fixed and filled any areas that needed ...shot in epoxy and then high build.

Image

Image

Image

Image

Image
User avatar
McShagger510
Posts: 1821
Joined: 26 Mar 2004 20:55
Location: East Van, Canada

Re: 71 1200 Project ( Picture intense)

Post by McShagger510 »

Awesome build so far! Gotta bring it out on some of our drives once its all finished.

Keep up the rad work!

James
The person with the sun in their eyes has the right of way. - my brother

'72 2dr. 510 Turbo
'73 240Z all stock
'71 2dr. 510 stock......for now
'91 Nissan truck *SOLD*
'02 TOYOTA Tacoma
'78 Kawasaki Z1-R
'84 Kawasaki GPZ750 Turbo
'99 Kawasaki ZRX1100
User avatar
tycot1
Supporter
Posts: 1295
Joined: 12 Oct 2006 18:22
Location: maple ridge, british columbia, canada

Re: 71 1200 Project ( Picture intense)

Post by tycot1 »

i am so happy to see rick getting into this datsun. i cant wait to see it finished. its going to be a nice 1200.
http://bigtimemotors.ca 1972 datsun 510 220 hp ka "couped", 1971 510 westwood champ gt4 '81& "83, 1979 550 hp trans am, 1962 cadillac hrdtp, 2005 subaru sti, 1999 triumph daytona 955i.
powerbench
Posts: 63
Joined: 17 Dec 2016 12:43
Location: Surrey, B.C

Re: 71 1200 Project ( Picture intense)

Post by powerbench »

Thanks Tyson,
It won't be any where near your quality , but I hope to have a decent example that I can gain some skills on and have some fun re living a bit of my youth . ( I just hope it doesn't gather the points I use to have)
More to come.....and you were right about that quarter panel......you'll see.
Thanks for all the kind words kids.
Post Reply