Thanks Greenthumb they do have have the halo rings.greenthumb wrote: ↑09 Dec 2018 21:36 Looks fantastic! Those dapper lights have the halo or angel eyes effect?
What did you do on your 510 today?
- eastbaysolo_73
- Supporter
- Posts: 705
- Joined: 18 May 2014 09:28
- Location: Northern California
Re: What did you do on your 510 today?
1970 2 door sr20det cookie cutter build
My build thread
http://www.the510realm.com/viewtopic.php?f=3&t=30772
Nor Cal Meng !
My build thread
http://www.the510realm.com/viewtopic.php?f=3&t=30772
Nor Cal Meng !
- eastbaysolo_73
- Supporter
- Posts: 705
- Joined: 18 May 2014 09:28
- Location: Northern California
Re: What did you do on your 510 today?
finally got the car off the jack stands this weekend. It still needs to have some suspension adjustments. But good enough for now.
nomorejacks by v p, on Flickr
nomorejacks by v p, on Flickr
1970 2 door sr20det cookie cutter build
My build thread
http://www.the510realm.com/viewtopic.php?f=3&t=30772
Nor Cal Meng !
My build thread
http://www.the510realm.com/viewtopic.php?f=3&t=30772
Nor Cal Meng !
-
- Posts: 107
- Joined: 27 Dec 2008 20:05
- Location: Fresno county
Re: What did you do on your 510 today?
eastbaysolo_73 wrote: ↑09 Dec 2018 19:48 Mounted the rear cross member today and rear coils. Need the car on the ground to make room for my wife's car.
Put on the rear wheels as well. I need to set the ride hight once I get the front suspension buttoned up and wheels installed.
Rearcoil by v p, on Flickr
rearwheel by v p, on Flickr
Where’d you get the qa1’s?
Re: What did you do on your 510 today?
Those mesh wheels look dope! I had some enkei 92 meshies on my first dime back in '95eastbaysolo_73 wrote: ↑17 Dec 2018 14:16 finally got the car off the jack stands this weekend. It still needs to have some suspension adjustments. But good enough for now.
nomorejacks by v p, on Flickr
- eastbaysolo_73
- Supporter
- Posts: 705
- Joined: 18 May 2014 09:28
- Location: Northern California
Re: What did you do on your 510 today?
Got them from here at DPracing.jefe de jefes wrote: ↑18 Dec 2018 21:30eastbaysolo_73 wrote: ↑09 Dec 2018 19:48 Mounted the rear cross member today and rear coils. Need the car on the ground to make room for my wife's car.
Put on the rear wheels as well. I need to set the ride hight once I get the front suspension buttoned up and wheels installed.
Rearcoil by v p, on Flickr
rearwheel by v p, on Flickr
Where’d you get the qa1’s?
http://www.dpracing.co
1970 2 door sr20det cookie cutter build
My build thread
http://www.the510realm.com/viewtopic.php?f=3&t=30772
Nor Cal Meng !
My build thread
http://www.the510realm.com/viewtopic.php?f=3&t=30772
Nor Cal Meng !
- eastbaysolo_73
- Supporter
- Posts: 705
- Joined: 18 May 2014 09:28
- Location: Northern California
Re: What did you do on your 510 today?
Nice! These wheels are 3 piece AME wheels, which are actually made by Enkei. They were only offered in Japan as there luxury brand.drawks wrote: ↑19 Dec 2018 07:31Those mesh wheels look dope! I had some enkei 92 meshies on my first dime back in '95eastbaysolo_73 wrote: ↑17 Dec 2018 14:16 finally got the car off the jack stands this weekend. It still needs to have some suspension adjustments. But good enough for now.
nomorejacks by v p, on Flickr
1970 2 door sr20det cookie cutter build
My build thread
http://www.the510realm.com/viewtopic.php?f=3&t=30772
Nor Cal Meng !
My build thread
http://www.the510realm.com/viewtopic.php?f=3&t=30772
Nor Cal Meng !
-
- Posts: 107
- Joined: 27 Dec 2008 20:05
- Location: Fresno county
Re: What did you do on your 510 today?
Thanks maneastbaysolo_73 wrote: ↑19 Dec 2018 11:27Got them from here at DPracing.jefe de jefes wrote: ↑18 Dec 2018 21:30eastbaysolo_73 wrote: ↑09 Dec 2018 19:48 Mounted the rear cross member today and rear coils. Need the car on the ground to make room for my wife's car.
Put on the rear wheels as well. I need to set the ride hight once I get the front suspension buttoned up and wheels installed.
Rearcoil by v p, on Flickr
rearwheel by v p, on Flickr
Where’d you get the qa1’s?
http://www.dpracing.co
- KiKiIchiBan
- Supporter
- Posts: 508
- Joined: 26 Feb 2014 23:46
- Location: London, England
Re: What did you do on your 510 today?
Not today, but I have finally primed my engine.
https://www.youtube.com/watch?v=wRZHzYc9NhI
I did try to start it, but it didn't fire up, I think there is something wrong with the coil, or with my knowledge, couldn't get a spark either way.
https://www.youtube.com/watch?v=wRZHzYc9NhI
I did try to start it, but it didn't fire up, I think there is something wrong with the coil, or with my knowledge, couldn't get a spark either way.
My P510 Bluebird SSS Coupe www.the510realm.com/viewtopic.php?t=26929
https://www.instagram.com/kikiichiban/
https://www.youtube.com/channel/UCBP1x8z2IBvfs-MQH2Gc73Q/featured
https://www.instagram.com/kikiichiban/
https://www.youtube.com/channel/UCBP1x8z2IBvfs-MQH2Gc73Q/featured
- bertvorgon
- Supporter
- Posts: 12021
- Joined: 04 Aug 2003 20:45
- Location: White Rock, B.C. Canada
Re: What did you do on your 510 today?
Unlike our poor compatriot above me, my car started on the 2nd crank, which surprised the hell out of me, it was 39F (4C) in the garage. My new storage garage, not that I'm complaining, has the attic hatch right above my car. So, when my daughter or son-in-law need to remove anything, or, in this case put the Christmas decorations away, I need to move the car. At that point I then need to let it run and bring it up to 200F. to eliminate any water/condensation.
As I have no choke I just let the float bowl fill up, give the throttle a 1/2 dozen good blips, to get the accelerator pump dumping a good slug of fuel in there, let it sit for 30 seconds to try to evaporate in the cold, then hit the starter. Wham, it virtually lit off with two cranks. I cycle all the relays, fan to high, wipers, lights, just to keep things moving. After 15 minutes slide the car back into it's slot and now can be good till spring.
I did remove the glove box, for a small project which I will start a thread on in case anyone is interested
As I have no choke I just let the float bowl fill up, give the throttle a 1/2 dozen good blips, to get the accelerator pump dumping a good slug of fuel in there, let it sit for 30 seconds to try to evaporate in the cold, then hit the starter. Wham, it virtually lit off with two cranks. I cycle all the relays, fan to high, wipers, lights, just to keep things moving. After 15 minutes slide the car back into it's slot and now can be good till spring.
I did remove the glove box, for a small project which I will start a thread on in case anyone is interested
"Racing makes heroin addiction look like a vague wish for something salty" - Peter Egan
Keith Law
1973 2 Door Slalom/hill climb/road race / canyon carver /Giant Killer 510
1971 Vintage 13' BOLER trailer
Keith Law
1973 2 Door Slalom/hill climb/road race / canyon carver /Giant Killer 510
1971 Vintage 13' BOLER trailer
Re: What did you do on your 510 today?
Installing a remote oil filter mount. Last week I got the filter mounted on the strut tower with the Traco mount. Today I installed the BRE remote filter block adapter and assembled the oil return hose.
- two_68_510s
- Supporter
- Posts: 3894
- Joined: 18 Apr 2010 11:20
- Location: Ben Lomond California
Re: What did you do on your 510 today?
AN 6?
Joel
2 '68 510 2 door sedans
'95 240SX
“We will either find a way, or make one.” – Hannibal
2 '68 510 2 door sedans
'95 240SX
“We will either find a way, or make one.” – Hannibal
- KiKiIchiBan
- Supporter
- Posts: 508
- Joined: 26 Feb 2014 23:46
- Location: London, England
Re: What did you do on your 510 today?
I started mine up for the first time
My P510 Bluebird SSS Coupe www.the510realm.com/viewtopic.php?t=26929
https://www.instagram.com/kikiichiban/
https://www.youtube.com/channel/UCBP1x8z2IBvfs-MQH2Gc73Q/featured
https://www.instagram.com/kikiichiban/
https://www.youtube.com/channel/UCBP1x8z2IBvfs-MQH2Gc73Q/featured
Re: What did you do on your 510 today?
Bolted on new wheels... New vto installed. Over inch clearance to wheelwell on rear and about 3/16 to control arm.. I think with a modified arm 225s will fit..
Mike Gibson
Datsun: 71 dime; 73 Z ; GT3 240
Other: 65 + 67 Mustang ; 03 murcie
Datsun: 71 dime; 73 Z ; GT3 240
Other: 65 + 67 Mustang ; 03 murcie
Re: What did you do on your 510 today?
More details please.
Wheel size and offset?
Tire size?
Wheel size and offset?
Tire size?